Aruba 203H Access Point : Cost-effective 802.11ac access point for branch offices and hospitality environments

Danh mục: Aruba, HP, Thiết bị mạng CISCO - HP - ATi, Wifi, Controller Aruba

This compact access point ensures the most cost-effective Wi-Fi connectivity for indoor premises including hotel rooms, dormitories, small offices and remote workstations. It’s software configurable to operate in either 1×1 dual radio mode, or 2×2 single radio mode.

Powered by PoE, it minimizes power consumption with rich features that further facilitates a highly efficient and reliable wireless network, and combines wireless and wired access in a single compact device.

This AP can be easily mounted to a standard data wall-box using the existing structured cabling system or converted to a desk mounted AP using an optional mounting kit.

Compare

Mô tả
Đánh giá (0)

Datasheet :

http://www.arubanetworks.com/assets/ds/DS_AP203H.pdf

AP-203H SERIES SPECIFICATIONS
Unified flexible radio 802.11ac 2×2:2SS hospitality and branch AP with internal antennas Supports wall-box and desk mount deployments

WI-FI RADIO SPECIFICATIONS

AP type: Indoor, flexible radio:
- 5GHz 802.11ac 2×2 MIMO OR 2.4GHz 802.11n 2×2 MIMO¹, or
- 5GHz 802.11ac 1×1 AND 2.4GHz 802.11n 1×11
Software-configurable radio supports 5GHz (Radio 0) and/or 2.4GHz (Radio 1)
5GHz: Two spatial stream Single User (SU) MIMO for up to 867Mbps wireless data rate to individual 2×2 VHT80 client devices
2.4GHz: Two spatial stream Single User (SU) MIMO for up to 400Mbps wireless data rate to individual 2×2 VHT40 client devices (300Mbps for HT40 802.11n client devices)
Support for up to 32 associated client devices per radio, and up to 8 BSSIDs per radio
Supported frequency bands (country-specific restrictions apply):
- 2.400 to 2.4835GHz
- 5.150 to 5.250GHz
- 5.250 to 5.350GHz
- 5.470 to 5.725GHz
- 5.725 to 5.850GHz
Available channels: Dependent on configured regulatory domain
Dynamic frequency selection (DFS) optimizes the use of available RF spectrum
Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
Supported modulation types:
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
Transmit power: Configurable in increments of 0.5 dBm
Maximum (conducted) transmit power (limited by local regulatory requirements):
- 2.4GHz band: +18 dBm per chain, +21 dBm aggregate (2×2 mode)
- 5GHz band: +16 dBm per chain, +19 dBm aggregate (2×2 mode)
- Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain
Maximum ratio combining (MRC) for improved receiver performance
Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
Short guard interval for 20MHz, 40MHz and 80MHz channels
Space-time block coding (STBC) for increased range and improved reception
Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
Transmit beam-forming (TxBF) for increased signal reliability and range (2×2 mode)
Supported data rates (Mbps):
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n (2.4GHz): 6.5 to 300 (MCS0 to MCS15)
- 802.11n (5GHz): 6.5 to 450 (MCS0 to MCS23)
- 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2 for VHT20/40/80)
802.11n high-throughput (HT) support: HT 20/40
802.11ac very high throughput (VHT) support: VHT 20/40/80
802.11n/ac packet aggregation: A-MPDU, A-MSDU

WI-FI ANTENNAS

Two integrated dual-band moderately directional antennas for 2×2 MIMO with maximum individual antenna gain of 4.3dBi in 2.4GHz and 6.3dBi in 5GHz. Built-in antennas are optimized for vertical orientation of the AP. The horizontal beamwidth is roughly 120 degrees.
- Combining the patterns of each of the antennas of the MIMO radios (in 2×2 mode), the peak gain of the effective per-antenna pattern is 3.8dBi in 2.4GHz and 4dBi in 5GHz.

OTHER INTERFACES

Uplink: 10/100/1000BASE-T Ethernet (RJ-45, back)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Efficient Ethernet (EEE)
- PoE-PD (input): 48 Vdc (nominal) 802.3af/at PoE
Local: 10/100/1000BASE-T Ethernet (RJ-45, bottom)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Efficient Ethernet (EEE)
Passive pass-through interface (two RJ-45, back and bottom)
- USB host interface (Type A connector)
- For Aruba LS-BT1USB BLE radio modules only
Visual indicators (LEDs):
- Power/system status
- Radio status
- Local network port status
Reset/LED control button (“paperclip access”)
- Factory reset (when activated during device power up)
- LED control: toggle off/normal
Serial console interface (custom, uUSB physical jack)

Đánh giá

Chưa có đánh giá nào.

Hãy là người đầu tiên nhận xét “Aruba 203H Access Point : Cost-effective 802.11ac access point for branch offices and hospitality environments”

Website này sử dụng Akismet để hạn chế spam. Tìm hiểu bình luận của bạn được duyệt như thế nào.

Categories

Aruba 203H Access Point : Cost-effective 802.11ac access point for branch offices and hospitality environments

Đánh giá

Related Products